GoodWe ESA all-in-one install in Perth: 15 kW inverter + 45 kWh battery

Updated 20/11/2026

GoodWe ESA all-in-one 15 kW inverter and 45 kWh battery installed in a Perth garage, Perth

Home › Blog › GoodWe ESA install, Perth

Perth, WAInstalled November 2026Three phase

GoodWe ESA all-in-one install in Perth: a 15 kW inverter with a 45 kWh battery

This week our team installed a GoodWe ESA all-in-one system with a 15 kW three-phase inverter and five 9 kWh battery modules, all in one neat stack on a Perth garage wall. Here’s what went in, why we chose it, and how the install came together.

By the Solar Red team · 6 minute read

GoodWe ESA all-in-one 15 kW inverter and 45 kWh battery stack in a Perth garage with a safety bollard

The short answer

  • System: GoodWe ESA all-in-one, 15 kW three-phase inverter plus five GoodWe 9 kWh battery modules.
  • Storage: 45 kWh rated, 44.25 kWh usable (8.85 kWh usable per module).
  • Where: a garage wall in Perth’s western suburbs, with a bollard in front and a dedicated AC isolator beside it.
  • Room to grow: the same stack can take more modules later without replacing anything.
  • Thinking about one? Send us a photo of your switchboard and the wall you have in mind and we’ll tell you if it fits.
In this guide
  1. What we installed
  2. What “all-in-one” means
  3. Why this system suited the home
  4. How the install went
  5. Safety and compliance
  6. Install photos
  7. Rebates and the interest-free loan
  8. FAQ

Big homes use a lot of power after the sun goes down: air-conditioning, pool pumps, cooking, hot water and everything else a family runs in the evening. This two-storey home in Dalkeith, in Perth’s western suburbs, already had solar on its tiled roof and a three-phase supply, so it was a good match for GoodWe’s three-phase ESA range.

What we installed

15 kWGoodWe ESA three-phase hybrid inverter (GW15KETA-G20)
45 kWhrated storage, 44.25 kWh usable
5 modulesGoodWe Lynx D G2 9 kWh packs (GW9.0-BAT-D-G20)
1 stackinverter on top, batteries below, on one garage wall
SpecThis installWhat it means for you
Inverter output15 kW, three phaseEnough power to run large loads straight from the battery
Solar inputUp to 30 kW of panels, 4 MPPTsPlenty of headroom if more panels go on later
Battery modules5 Ă— 9 kWh (8.85 kWh usable each)44.25 kWh you can actually use
Battery chemistryLFP (lithium iron phosphate)The stable, long-life chemistry we prefer for homes
Rated cycle life10,000+ cycles (GoodWe figure)Built for daily charging and discharging
Weather ratingIP66Sealed against dust and water
ExpansionUp to 12 modules (6 in a single stack)Can grow if the household’s needs change

Specs from the GoodWe ESA Series (5–30 kW, three phase) and Lynx D G2 Australian datasheets. Usable energy is GoodWe’s beginning-of-life figure.

What “all-in-one” means

With most battery systems, the inverter hangs on the wall and the batteries sit separately, with cabling between them. The GoodWe ESA puts it all in one stack. The inverter sits on top, the battery modules slot in underneath, and the whole thing stands as one tidy unit.

One neat stackInverter and batteries in a single column, so there’s less wall space used and less exposed cabling.
Modules that plug togetherEach 9 kWh pack stacks on the one below. GoodWe allows mixing capacities in the same series, so adding more later is simple.
Built-in fire suppressionGoodWe builds an aerosol fire suppression system into the ESA, with multiple layers of protection.
Whole-home backup readyThe ESA supports whole-home backup and switches over in under 4 milliseconds, according to GoodWe.

Why this system suited the home

Three-phase supply

The ESA we installed is a three-phase system, built for homes like this one with a three-phase meter. It shares the load across all three phases instead of pushing it all through one.

A large household load

A home this size needs both capacity (kWh) and power (kW). Five modules give the storage, and the 15 kW inverter gives the power to run big appliances from the battery at the same time.

Solar already on the roof

The home already had panels on its tiled roof. The battery stores the daytime surplus so it can be used in the evening instead of being sold back to the grid for a few cents.

A garage that fits

A single column of five modules plus the inverter needs a clear stretch of wall. This garage had it, close to the switchboard and out of the weather.

How the install went

The whole job was done in one day by our local, accredited Perth installers. We take pride in our work, and it shows in the details: straight conduit runs, every isolator and label in place, and a garage left as clean as we found it. Here’s the order we worked in.

Site check and roof inspection

We checked the existing panels on the roof, then confirmed the battery spot and clearances in the garage.

Standing the stack

The five battery modules went in first, each one locked onto the one below, with the ESA inverter on top. Every module has its own power button and DC isolator on the side.

AC isolator and conduit

We mounted a dedicated inverter AC isolator next to the stack and ran all the cabling in conduit up the wall and into the ceiling.

Switchboard work

At the switchboard we fitted a dedicated three-pole main switch for the inverter supply, labelled it, and added the “multiple supplies” warning sign.

Labels, bollard and commissioning

The stack got its safety signage and shutdown procedure, a bollard went in front to protect it from cars, and then we commissioned the system.

Safety and compliance

Every battery we install has to meet AS/NZS 5139, the Australian standard for battery systems. In practice, that came down to a few key things on this job.

Done on this job: installed in a garage (not a habitable room), clear space around the stack, a bollard where a car could reach it, a separate AC isolator, the shutdown procedure on the unit, and warning labels at the battery and the switchboard.

Want to know if your garage or wall would pass? Our Perth battery location guide covers the clearances in detail.

Install photos

Here’s the finished job, start to finish.

Rebates and the interest-free loan

A system this size qualifies for real support. The federal Cheaper Home Batteries rebate applies to eligible batteries Australia-wide, and WA households can also use the state battery rebate and the interest-free battery loan through Plenti. Solar Red is a Plenti-approved retailer, so we handle the paperwork for you.

Timing matters: the federal rebate steps down on 1 January 2027. Here’s what changes and how to lock in today’s rate.

For the details, see our guides to the federal battery rebate, the WA battery rebate and the interest-free battery loan.

Frequently asked questions

What is the GoodWe ESA?
It’s GoodWe’s all-in-one home battery system. The hybrid inverter and LFP battery modules come in one stack. The three-phase ESA range covers 5 kW to 30 kW inverters and up to 108 kWh of storage.
How much of the 45 kWh can you actually use?
44.25 kWh. Each 9 kWh module has 8.85 kWh of usable energy, according to GoodWe’s datasheet, and there are five modules in this system.
Can more modules be added later?
Yes. GoodWe allows up to 12 modules in a system, or up to 6 in a single stack, and lets you mix capacities within the same series. We check your space and inverter before adding any.
Will it keep the house running in a blackout?
The ESA supports whole-home backup and switches over in under 4 milliseconds, according to GoodWe. What stays on depends on how the backup is wired at your switchboard, so we set that up with you at quote time.
Do I need three-phase power?
Not for every GoodWe system. This install used the three-phase ESA because the home has a three-phase supply. GoodWe also makes a single-phase version, and we’ll tell you which one suits your meter.
Is a garage a good place for it?
Usually, yes. A garage is our first choice in Perth: it’s shaded and dry, and it’s often close to the meter box. We fit a bollard wherever a car could reach the battery.

Want a system like this one?

We take pride in every install we do, big or small. Send us a photo of your switchboard and the wall you have in mind, and we’ll tell you what fits before you commit to anything. Local Perth installers, Plenti-approved for the WA rebate and interest-free loan.

Call 1800 449 733Get a free quote

Keep reading

More Perth battery guides

See every guide in one place: Perth solar battery guides.

Sources: GoodWe ESA Series 5–30 kW three-phase datasheet (AU); GoodWe Lynx D G2 GW6.0/GW9.0-BAT-D-G20 datasheet (AU); AS/NZS 5139:2019 Electrical installations: Safety of battery systems for use with power conversion equipment.

Call 1800 449 733Free quote
Google reviews